Electric Skateboard Motor 6355 190KV

MAXIMUM STATOR SIZE - Other motors of similar size use smaller sized stators in the same size motor can length. We do our best to shorten length of our motors and expanding our stators to the biggest size we can fit. This gives you the best of both worlds as we have smaller sized motors and larger sized stators. Ultimately, this means increased performance for less bulk.

BATTLE HARDENED - All motors are battle hardened inside the motor which means we add in another production step to epoxy every neodymium magnet to the motor can. This means that as you rack up the mileage on your powerful motors your magnets stay in place. Loose and falling magnets are a thing of the past.

BATTLE HARDENED PLUS - On top of battle hardened motors, we include mechanical retainers on the back and front side of our neodymium magnets which prevent any shifting or loosening during high performance operation.

CNC VENT HOLES - CNC Vent holes improve efficiency and keep your motors cool. No more overheating motors due to heat and inefficiencies. Your motors will be able to run harder and faster. No more burning out your motors. Vent holes within our design will ultimately keep your motors running cooler than comparable motors with no vent holes. Due to heat not being able to escape from your motor can. Truth be told, vent holes take additional production time to CNC additional holes in each and every motor can which can add production costs to a motor design. All holes have been designed in locations to prevent exposure to rocks and debris while riding. For more rigorous riding we will have an upgraded mesh screen that can be attached to the backend of the motor for complete enclosure from rocks and debris.

UPGRADED HALL SENSORS - We've upgraded our motors with more accurate and efficient sensors by adding a sensor slot on the actual stator. This improves accuracy for using sensors with VESC designed ESCs especially. The accuracy for each hall sensor angle is much closer to each other versus the previous sensor pcb version. Now with the new design sensors are much more unlikely to fail and we get improved accuracy and efficiency. Previous hall sensor differences were about 10-20 degree in angle difference. The new and improved hall sensor differences are about 1-3 degrees in difference. Now that we typically always run motors in sensored mode. This is a huge benefit and upgrade.

HIGH TEMPERATURE MAGNETS - All of our motors use high temperature neodymium magnets to withstand high performance operation. Similar motors will downgrade to lower temperature magnets to lower costs but we want a high quality motor capable of high temperature if needed.

RUBBER SEALED BEARINGS - We use upgraded rubber sealed bearings on all bearings in our motor to extend the life of your motors. Cheaper metal shielded bearings which are very common in other similar sized motors are easier to become contaminated as they are more likely to introduce dirt, dust and grime into your bearings which will result in a shorter bearing life. Rubber sealed bearings have less maintenance. They prevent lubricants from seeping out and contaminants from seeping into the bearing. Take for example on your skateboard wheels, what bearings would you want on your skateboard wheels? Ideally, the rubber sealed bearings so why would you want something different for your electric skateboard motors?

SMOOTHER MOTORS - We add additional rubber sealed bearings support on our all of our motors. Standard motors typically have only 2 bearings even for a larger motor like a 6374 6380 63100. We upgrade all of our motors with an additional 5+ rubber sealed bearings for smoother operation. Motors will typically spin 2-3+ times more than our wheels/tires will spin. Providing additional bearing support is crucial for motors because if our bearings fail our motor will fail.

UPGRADED DRIVE SHAFT - The insane torque that these motors generate can break the shaft from the motor can which result in the motor shaft spinning around inside the motor can. Most motors will typically use smaller screws and inferior methods that result in this being a common occurrence. We've upgraded our drive shaft to include a 4 point system on the end of the motor can to effectively secure the motor shaft to the motor can that can withstand the torque that our motors generate. If this is an issue, our warranty will replace it with a new motor.

CONTINOUS IMPROVEMENT GUARANTEE - We strive to improve efficiency, durability, performance, and reliability which will increase the motor life span. Our guarantee to our customers is that we work to continuously improve our motors after every production run. Every production run we learn and understand how better to improve and produce better motors so our customers have confidence in knowing that they are purchasing the best motor possible. If you have any suggestions, please let us know. We are always trying to improve.

MOTORS DESIGNED IN-HOUSE - We have full CAD designs of the internal components of our motors. This means that we have full control of the production quality of our motors while our designs are a secret and our competitive advantage. We do our best to deliver the best quality motor that we can. Standard motors are now a thing of current times. What does this mean? This means that similar sized motors now have a standard motor which is a motor designed specifically for lower cost and shorter production times but this isn't a good thing because many features and upgrades are sacrificed for the result of less cost and lower production times. Of course, we have the option to do the same but we prefer to offer a higher quality motor at a comparable price point to standard motors in the industry.

WARRANTY - We believe in the motors that we produce. We offer a 6 month warranty on all of our motors upon proof of failure.

Maximum Performance = These motors will allow you to travel up to speeds of 25-35+ mph. Maximum speed is dependent on available battery power, electronics and gearing ratios. I've climbed 20-25 degree inclines with these motors in San Francisco hills for up to 200 lbs rider weight for more upgrade to Dual 6374 Electric Skateboard Motors.

• Max Power = 2500 Watts
• Max Amps = 80 Amps  
• Max Volts = 4S-12S+ (Capable of more but should be tested.)
• Max Torque = 2.83Nm
• Max RPM = Voltage * KV (190KV)
• Motor Weight = 1.41 lbs
• Recommend ESC = 12S 40-120+ Amps (TORQUE6 DUAL ESC)
• Motor Shaft = 8mm Shaft Diameter, 32mm length useable shaft, (2) flat spot w/ 3x3 keyway slot.
• Motor Wire = 200mm silicone 12AWG wire with MT60 Yellow Connectors.
• Sensor Wire = Standard VESC Connector JST-PH 6pin 2.0mm pitch

☑️ What Electric Skateboard Can I Build?

With our 6355 190KV motors. You can build lightweight single motor electric skateboard or a high performance lightweight dual motor setup that will fly you above 20-25% inclines or more.

The single or dual 6355 motor setup is ideal for younger kids, college students, beginners and commuters.

If you prioritize light-weight and nimble electric skateboards, better portability and maneuverability. These motors are for you!

Lighter motors are much easier to carry when commuting and larger motors are not necessary.

If you need an electric skateboard for daily transportation, a lightweight and smaller board will be more agile and responsive.

Our high performance 6355 motors are also much more affordable than our heavier and more powerful options.

In general, if you are looking for fantastic value and the best light-weight motors the 6355 190KV Electric Skateboard Motor is exactly what you're looking for.

☑️ Will This Motor Fit My Electric Skateboard? Motor Compatibility?

If you are building a brand new electric skateboard and using TORQUEBOARDS parts. Yes, this motor will fit your electric skateboard.

If you are re-building or repairing an electric skateboard. There are a few things that you must check to confirm that this motor will fit. If you need any help, simply send us an email and we can confirm.

What is the motor shaft diameter? Typically, the diameter is 8mm or 10mm. Those are typically the standard motor shafts. 8mm being the most common option.

What is the motor shaft length? Length of the motor shaft may be something to check if your setup is using a belt cover. You don't want the motor shaft length to be either too long or too short.

What is the motor shaft shape? There are two types of motor shafts. They are circular/circle shape or D shape which are typically still circular they just have a notch on the motor shaft that looks like a D shape.

What is the motor wire connector? There are 3 wires that come out of the electric skateboard motor and we use an MR60 connector. If you use our Electric Skateboard ESC/VESC it will have an MR60 connector so no need to change the wires and they will connect with no issues. If you have a different ESC you may need to solder and swap the connector for the opposite MR60 connector that way they can connect together. Ideally, it’s best to make an adapter wire instead of soldering the connector on the ESC.

What are the hall sensor wire connector? There are 6 wires for the hall sensor and typically it’s a smaller white connector. If your hall sensor is a different plug (located on your ESC) you may need to create another adapter to connect them to your setup.

What about wire length? Wire length for the motor wires and sensor wires will typically depend on your electric skateboard setup as they are typically dependent on how you mount the motors and the deck/enclosure that you use. You can extend the wires but they will require soldering help.

If for any reason, you don't know and need assistance. Simply, just send us an email.

☑️ Our Recommendations - Who are these motors not for!

These motors aren't recommended if you want to aggressively ride up steep hills hard and do it back to back 4 to 5 times almost immediately. If you’re typically a heavier rider weight 250lbs+ a bigger motor will be better. You’ll typically want bigger motors that are capable of more stress and heat.

If you want a chill cruising board that is more compact and lightweight than anything else. The 6355 190KV motors are your best bet.

If you want a more powerful electric skateboard motor. We would recommend our 6374 190KV Motor, 6380 190KV Motor or 63100 190KV Motor.

☑️ Compatible 6355 Motor Mount

If you are looking for a compatible 6355 motor mount. We suggest our electric skateboard motor mounts. All of our motor mounts will fit all of our 63mm series motors.

☑️ Compatible Belt Drive Kit

If you are looking for a compatible belt drive kit. You can go with a full mechanical kit for a single motor kit or a dual motor kit.

We recommend our 218mm Longboard Trucks as it is the proper truck size for our 63mm motors.

You can buy the electric skateboard pulleys separately, we have two longboard wheel options which are an ABEC or KEGEL style core and you will have to attach the pulley to the longboard wheels core. There are specific electric skateboard wheels which have the ABEC or KEGEL core.